The number of screw speed should not be large, because of frictional processes for possible overheating of the melt. Moulding mass reaches the optimum plastification at 180-200 degrees centigrade and high pressure (150-300 bar). When injected into the calibration element extruder, especially in the first, successful PVC molding melt should have a low viscosity, but being tough. Granular or powder enters the extruder through a special funnel. To fully loaded hopper on the equipment with cylindrical screws metered volume of powder form was applied at each turn the screw. Special dispensers were installed for conical screws. This made it possible steps to configure the bandwidth equipment. For ensure control and fine tune the bandwidth of equipment to improve the quality of profiles in our time, gravimetric dosing devices are equipped with cylinder and extruder screw.

Method Equipment is a post from: John Otis

For example, if a combination of tile flooring and kitchen area will be allocated from the general interior of the apartment. Whatever coating you choose, kitchen should be in harmony with the rest of the apartment interiors, and much depends on the shape and size of the kitchen and on your furniture. However, the most important thing for any kitchen – is safe and most comfortable conditions for work. No beauty can not be justified, if at the time of cooking and other kitchen work owners are constantly in danger of injury. It has become fashionable to organize the kitchen area on the podium, and even when it is technically unfounded.

In this case the owners often do not think about how they will move out of the kitchen into the dining room and back, carrying the dishes and trays of food. Formed in the device the catwalk step can cause constant discomfort and serious injury, so you should always keep in mind about the basic purpose and plan for its cuisine with maximum security. In general, the material for the kitchen flooring must be not only durable, beautiful, and water resistant, but also safe, allowing the kitchen to feel free and comfortable. To take into account all these factors, as well as compliance with the basic your kitchen style apartment or house, it is best to use the services of professional designers.

Natural Kitchen is a post from: John Otis

For wooden houses light construction, pier foundation is the most common. Let's look at how the projects done and pier foundation under the house. To begin digging a trench having a cross-section of 30 cm or more. After that, the corners of the house put poles (piles). Especially pay attention to the installation of poles in the joints of the outer and inner walls of the house. Pier foundation for light homes without basements It also lays the walls of brick when you need deep foundations and foundation-type tape is expensive.

For the construction of pier foundation is most frequently used blocks of prefabricated concrete or reinforced concrete. The choice of material depends on the number of floors and building mass. Pier foundation placed in locations where the most concentrated load. At the heart of the foundation pillars that are arranged by drilling wells to a depth of 2.0 m in increments of 1.5 – 2.5 m diameter of 250-400 mm. Parks vertical bar (3 – 4 pins) with the release of grillage and poured concrete. Next, a trench is arranged under the concrete sand cushion tape (grillage) deep 200 – 300 mm in width and covered with grillage coarse sand from plugging. Parks reinforcement cage grillage with a bandage to the armature poles. Width grillage 250 – 400 mm, height 400 mm.

Pier Foundation is a post from: John Otis

The level of lighthouses for each room set is different. It depends on the thickness of the finished floor it for granite is from 12 to 15mm, with light adhesive. For wood floors – 18 – 25mm thick plywood with a view of 8mm. The thickness of the second layer of screed is 20 – to 10mm. Therefore, the upper level of rough tie will be on average 30 – 45mm lower than the fine finish floor.

It must be remembered that the thickness of the rough layer of screed should be not less than 30mm. If the thickness is less then quickly buckle and crack would have to dismantle and make a new one. This is due to the fact that the layers of rough tie, made of Portland, and their composition is designed for installation in layers with a thickness of 30mm. It is more economical than using more expensive samoniviliruyuschie compositions for the entire thickness of the screed. If the tie needs to be done with thickness less than 30mm, it is necessary to apply samoniviliruyuschie solutions. Screed floor. Before pouring screed base should be cleaned from dust and debris and primed it a special primer for better adhesion ties and bases.

The Thickness is a post from: John Otis

Incidentally, the thin film is higher than that of fat, so do not try to put a lot of paint on the surface, exceeding the optimum (recommended by the manufacturer) value. In addition, to paint a good lie down on the surface, it must be a corresponding viscosity, and to avoid any leakage of dye is introduced so-called thixotropic additives. Thixotropy – the ability to increase the fluidity of the material under mechanical loads. When choosing paint for use vinterere, special attention should be paid to its environmental friendliness and safety. Andrei Nazarenko, category manager "Henkel Bautechnik (Ukraine)", notes that consumers have become legible when selecting construction materials and pay particular attention to issues of environmental security. Dmitry Musiyenko, Head of Sales LLC "Giant", said that a truly environmentally friendly paint should be odorless. In addition, the responsible manufacturer necessarily indicate a capacity class durability and European environmental certificate TUV. Most friendly to the environment – paint with the international symbol on the packaging of the "Blue Angel" – a symbol of absolute purity and environmental safety products.

The Choice Of Wall Colors And Wallpaper is a post from: John Otis

Silicon surface under the enamel is prepared in the same way as under the alkyd paint. In some cases, you can do without the primer and enamel applied immediately after cleaning the surface. Organosilicon enamel differ good shine and clean tone. Sales are domestic production marks the enamel KO-168 (white, yellow, red, brown, blue, green and black), KO-1112 (white, yellow, blue, brown, turquoise and green) and CR-835A (spray). In addition, commercially available grade enamel KO-84 and CA-814 – heat-resistant enamel silver, and CR-174 – especially for facades. Diluted enamel KO-168 and CR-1112 solvent 646 or turpentine, is applied in two coats by brush or spray.

Each layer is dried for 2 h. Most of these enamels are used to repair damaged areas on the surface of metal, enamel and the restoration of cleaved etc. Small paint defects, less than 5 mm long, invisible paint is quite simple. This is best done with a gun. Featuring fast-drying NITROEMALI under normal conditions (30-60 min.) Nitroemali give Solid solid film that can be polished to a mirror finish, rather resistant to moisture, mild acids and alkalis, petroleum products. Nitroemali widely used not only for domestic but also for outdoor painting, painting for appliances, furniture, various household items, as well as for many industrial purposes. The disadvantages are nitroenamels flammability of their films, low thermal stability (up to 80 C), as well as propensity to aging and cracking of sunlight.

Disadvantages is a post from: John Otis

Federal Centre Resources is a post from: John Otis

If it is the walls and everything connected with them, then they must be primed. After all these simple manipulation can start working. 'Keramoizol' applied a thin layer, one layer should not exceed 0.5-1.0 mm. drying time is 24 hours at temperature of 20 degrees. The number of layers ranges from 3 to 6 (based on the needs of the object, for the walls need less layers, for pipe more) with a maximum thickness of 3.5 mm (double thickness has the effect will not give) Maximum temperature for the material from 5 to 95 degrees, and no more, because it may cause material damage and no less than 5C, the material in the liquid state is afraid of freezing. To work in the winter time, you need a 'Keramoizol' on the basis of the varnish. A after drying it 'Keramoizol' can withstand -50 to 250 degrees.

Regarding the amount of material, it will be 1:1, ie, 1L to 1 square meter. Should leave at least a layer of 1.5-2.5 mm. On the Internet, you probably have seen many, as positive and negative opinions and impressions. I want to say just one thing, there is a negative for the incorrect use of the material and non-compliance with the recommendations that are simple and clear. Since, there have been instances when walls with insulation, covered with a layer of more immediately without waiting for the drying of the previous layer, thus damaging the bottom layer of insulation, after which it become loose and fall – all the work in the pipe … There were some cases where only covered one layer and all, and then said that it does not work, and insulation is poor. There were different cases. But most people who do everything right – happy with the results of the thermal insulation Keramoizol. Therefore, reading Documentation is the key to success. But why are we so used to doing that first, and then read Personally, I myself, insulate your house with this material and the results surprised me. Try it and you'll also be surprised! If you need advice on equipment insulation 'Keramoizol', the site find my phone number, type I, and I'm happy to answer all your questions! Thank you for your attention.

Maximum Keramoizol is a post from: John Otis

Since 2001, ‘TSZP’vypolnyaet the reconstruction of the geometric dimensions and application of corrosion-wear resistant coatings on the working surfaces of stems and guides for the branch of JSC “RZD”. Since 2005, the Company ‘TSZP’ performs work involving the application of corrosion-resistant coatings for wear-resistant surface plates and plates for OAO Tver Carriage factory ‘. Since 2006, work is underway to restore the equipment for the Moscow metro. The group of companies ‘technological system of protective coatings’ (OOO ‘TSZP’) for 16 years has accumulated vast experience in restoring, strengthening, improvement of operational and physical-mechanical characteristics of the working surfaces of machine parts and mechanisms, methods of thermal spraying and welding. We have delivered more than 20 lines of application thermal coatings ‘turnkey’ in various industries.

All equipment collected in Russia from the high-quality imported and domestic components to optimize cost and quality produced equipment. The possibility of multiple parts repair methods can include thermal spraying technology to resource data. Many developments have no analogues in the world and protected patents.

Tver Carriage Equipment is a post from: John Otis

The most striking example of the use of advanced technology is the automation of many tasks by computer. Offices today are full of diverse computer technologies to help solve many aspects of business – document management, financial accounting, presentation and so on. If we draw a parallel with the telephone network, it becomes clear – the local network for computers is not as important as the telephone lines for people. Without the information message between computers transfer information from one person to another is extremely difficult, and some tasks are simply impossible. Although we do not see with the naked eye the existence of networks in the office, believe me – they are in each. Design and installation of local networks – a complex and time-consuming task, which is under power is not for everyone.

Must consider many factors – the number of computers, their geographical location, the bandwidth required, the points with maximum load, and more. That is why the installation of local networks is to instruct professionals who are facing this challenge every day and know how to solve a particular problem. Ltd. "System" – a recognized leader in computer maintenance, and work with local networks – one of many services we provide. By contacting us you will be able in practice to make sure than earned our high reputation. Installation of local networks of LLC "SYSTEM" – the belief in an ideal work of computer networks and the highest level of service. If your needs are not limited to local area networks – take a look at our range of services, and you will understand that we are not just another service company, and a reliable partner for your business to ensure the smooth operation of the information structure of your company. Source article -.

Installation Of Local Networks is a post from: John Otis